9020 / 9021

Mixing of low up to highly viscous media

9030

Mixing of media with low and middle viscosity < 500 mPa s

9025

Mixing of media with low and middle viscosity

9610

Mixing of viscous up to highly viscous media

9209

Mixing of media with low and middle viscosity

9103

Mixing of media with low and middle viscosity

9003

Mixing of media with low and middle viscosity

9503

Mixing of media with low and middle viscosity

9403

Mixing of media with low and middle viscosity

9053

Mixing of media with low and middle viscosity

9703

Mixing of media with low and middle viscosity

9603

Mixing of media with low and middle viscosity

MD-24

Magnetic drives are designed for agitating a fully vacuumed flask. Multi-functional easy to replace impeller.

5.101.1.7

Universal Stirrer Guides for use with standard taper ground glass joints can be used with PTFE Shaft Stirrers and glass and meatal shaft stirrers.

8050-02

The newest design of mechanical stirring seals with all parts that are in contact with liquid or vapor being made of PTFE,RULON, or PEEK material.

KA22-02

Universal PTFE Stirrer Seal

5.0.0619

This product is designed to provide an effective guide for Glass and Metal Shaft stirrers over a range of temperatures without shedding particles from the seal, whilst maintaining a vacuum.

8117-10

A superior, low melting, silicone-base lubricant which liquifies at body temperature.

8118-10

Smooth, stable, odorless oil based lubricants, free of silicone, suitable for lubrication of joint and piston. The melting point is 52℃ , can be cleared with xylene.

8119-07

Resistance to acid and alkali, soluble in organic solvents, and suitable for oxidizing gases. The temperature can reach260℃ it is non-combustible, and non-oxidized.

8115-08

Good chemical stability, no reaction with oxygen, hydrogen, hydrocarbons and other chemical substances. The usable temperature range is -35℃ ~ 290℃ .

8116-10

Very low vapor pressure, highly inert, nonflammable grease.

8081-05

SHAFT Fully flexible drive shaft connects the motor to any size or type of reactor stir shaft.

The design of the electrical “Lift 240“ is identical with that of the mechanical 240 x 240 mm WIGGENS lab jack. Both va...

KA11-91

Available to support experiment tools such as stirrers, water baths, flasks and etc in height control

11090-17

All-position holder connects at any angle in any plane. Consists of two holders connected by double plate-joint which sets holders 900 from each other.

KA00-52

Three-Prong Clamps

11084-11

Universal Swivel, “Power Hold”

KA00-50

Two-Prong Clamp, Dual adjustment clamp has a maximum grip size of 73mm. Two-prong design is ideal for beakers, flasks, and test tubes. Jaws adjust independently. Overall length is 255mm. Clamp extends 127mm

KA00-57

Grips rods up to 3/4 in. diameter (19mm). Holding angle of jaw is adjustable. Can be locked with a wingnut. Wingnut also allows length adjustment.

KA00-58

Grips rods up to 3/4 in. diameter (19mm). Holding angle of jaw is adjustable. Can be locked with a wingnut. Wingnut also allows length adjustment.

KA00-68

Material : Die Casting (Chromium plating) Pipe Diameter : Ø12.7mm

KA00-73

Material : Die Casting (Chromium plating) Pipe Diameter : Ø12.7mm

KA00-71B

Material : Brass (Chromium plating) Adjustable angle holder, different from the other holder fixed at 90 degrees

KA00-65

Material : Stainless Steel (Chromium plating) For Funnel & Separatory Funnel

KA00-67F

Material : Stainless Steel (Chromium plating) Separatory Funnel Size : 250ml-70mm / 500ml-90mm / 1,000ml-100mm

11080-19

(Regular) Will grip rods up to and including 19mm diameter. Attaches clamp at right angle.

KA00-70A

Heavy-Duty Clamp Holder, Jumbo clamp holder has amaximum grip size of 22mm Heavy duty version of the regular holder is for use wherever clamping at 90° angle is required

WH2

Only suitable for Single Rod Stand

WH1

Only suitable for Single Rod Stand

KA00-71

Material : Stainless Steel (Nickel plating)

WH4

Only suitable for Double Rod Stand

KA00-72

Material : Brass (Nickel plating)

WE-11

Extend the rod to the expected length for your application

KC.KCM14

Material : Nickel

KA00-56

Material : Stainless Steel / Vinyl Coating

WH11-S

(Stand with base plate H-shape)

KA00-69

Lab frame hook connector allow one-handed assembly of two components with one adjustment screw. Material : Die Casting (Chromium plating) Pipe Diameter : Ø12.7mm

WH11-D

(Stand with base plate H-shape)

KA00-50D

Gooseneck Extension Clamp, Vinylized Jaws

5.230.2

Can be used up to a max. temperature of 280℃

5.330.2

Can be used up to a max. temperature of 280℃

5.430.2

Can be used up to a max. temperature of 280℃

5.80850.300

Can be used up to a max. temperature of 280℃

5.530.1

Can be used up to a max. temperature of 280℃

5.100830EX

Can be used up to a max. temperature of 280℃

2.052.1

桨片可以安装在上述搅拌轴上,防腐蚀，并且不会掉碎屑

5.606040

Can be used up to a max. temperature of 280℃

5.706070

Stainless steel core surrounded by PTFE mantle

5.90850

Stainless steel core surrounded by PTFE mantle

9610

Mixing of viscous up to highly viscous media

9403

Mixing of media with low and middle viscosity

9053

Mixing of media with low and middle viscosity

9703

Mixing of media with low and middle viscosity

9603

Mixing of media with low and middle viscosity